The Linux Wacom Project
SourceForge.net Logo

Linux Wacom Project HOWTO

3.1 - Testing Tablet Detection






In this section we will determine which driver, if any, claims control over the tablet. There are at least two drivers that are interested:
1) (usb)hid.o which may think it is an HID device (for kernel 2.6.17 or older),
2) the wacom driver which should identify the tablet as its own.

To see which driver is driving the tablet, issuing more /proc/bus/usb/devices should list something similiar to the following:

[jej@ayukawa wacom]$more /proc/bus/usb/devices
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=056a ProdID=0042 Rev= 1.15
S:  Manufacturer=Tablet
S:  Product=XD-0608-U
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=140mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=wacom
E:  Ad=81(I) Atr=03(Int.) MxPS=  10 Ivl=5ms

where Vendor=056a indicates a Wacom device. Driver=wacom means Wacom driver is in control of the tablet. If you see anything other than wacom after Driver=, at least hid-core.c needs to be updated.

On newer 2.6 systems, more /proc/bus/input/devices gives you

[jej@ayukawa wacom]$more /proc/bus/input/devices
I: Bus=0003 Vendor=056a Product=0042 Version=1.15
N: Name="Wacom Intuos2 6x8"
P: Phys=usb-0000:00:1d.1-2/input0
H: Handlers=event3
B: EV=1f
B: KEY=1cff 0 1f00ff 0 0 0 0 0 0 0 0
B: REL=100
B: ABS=f00017b
B: MSC=1

where, again, Vendor=056a indicates a Wacom device. Name="Wacom Intuos2 6x8" means an Intuos2 6x8 tablet reported to /dev/input/event3. If there is no Wacom after Name=, you need to update wacom.c.

On older 2.6 kernel systems, unplug then replug your tablet after issuing tail -f /var/log/messages, you should see a flurry of activity. The exact output depends a lot on your particular kernel and distribution.

This is Suse 10.2 (2.6.25.20-0.7):
[jej@ayukawa usb]# tail /var/log/messages usb 2-2: USB disconnect, address 2 usb 2-2: new full speed USB device using uhci_hcd and address 3 usb 2-2: configuration #1 chosen from 1 choice input: Wacom Intuos4 6x9 as /devices/pci0000:00/0000:00:1f.4/usb2/2-2/2-2:1.0/input/input8 usb 2-2: New USB device found, idVendor=056a, idProduct=00b9 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: PTK-640 usb 2-2: Manufacturer: Tablet

If all went well like above, the USB device was successfully detected and handled by the wacom driver. This presumably means that information like pressure and tilt will be received on /dev/input/event3. You are ready to configure the X driver Downloading the Code.

If instead you got any of the following lines in your log, the wacom driver did not get control. Either your wacom driver doesn't support your tablet or hid is in control.

	input0,hiddev0: USB HID v1.00 Mouse [Tablet PTK-640] on usb1:5.0
	input0: Tablet PTK-640 on usb1:5.0







Copyright (C) 2002-2011 - LinuxWacom -Last updated July 23, 2012
This website and its contents are licensed under the GNU GENERAL PUBLIC LICENSE.